A Step-by-Step Guide to Setting Up a Tub
A Step-by-Step Guide to Setting Up a Tub
Blog Article
The writer is making a few good points on Installing A Bathtub as a whole in this post down below.
Mounting a tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old bathtub is readily available, the task can move rapidly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either instance, the project is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub and set in the new one. See to it you have actually qualified yourself for the task and also are comfortable attempting it. Instead of working with a service provider to take over a halfway-completed project, it is better to think about utilizing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This write-up will assist you set up a brand-new bathtub in your shower room if you have actually already purchased a brand-new tub as well as do not require to change the plan of your previous water pipes.
Your tools as well as product list should comprise the following:
Preparing for the Installation
Firstly, the supporting framework provided with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable tap connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The process of removing the existing faucets can be quite troublesome as a result of the restricted access that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. Once the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before moving on to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wood boards under its feet, put the bath tub in the needed position. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub till the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost flexible tap adapter to the suitable supply pipeline by making a compression join; then do the exact same for the various other tap.
Turn on the water and examine all joints and new pipework for leakages as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the bath tub needs to wait until the tub has actually been used at least when as this will certainly resolve it into its final setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Safeguard the faucet in place with the manufacturer offered backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The previous type ought to be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, causing the water to permeate the wall between the bathroom and also the tiling, causing problems with wetness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, and also can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can split fairly early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen person who reads about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that excerpt was beneficial. Remember to take the time to share this content if you liked it. I cherish reading our article about Tools You Need to Install a New Bathtub .
Click Here!
Report this page